Mercedes C-Class

W203 since 2000 of release

Repair and operation of the car



Mercedes-Benz
- Mercedes-Benz cars of class C (W-203)
   Identification numbers of the car
   Acquisition of spare parts
   Technology of service, tool and equipment of a workplace
   Poddomkrachivaniye and towage
   Start of the engine by means of the auxiliary rechargeable battery
   Automobile chemicals, oils and lubricants
   Diagnostics of malfunctions
+ Operation manual
+ Routine maintenance
+ Engine
+ Cooling system and heating
+ Power supply system and release
+ Engine electric equipment
+ Manual transmission
+ Automatic transmission
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment


a45480c7





Diagnostics of malfunctions

The description of diagnostics of electronic control systems and diagnostic codes are provided in the Head Elektrooborudovaniye of the engine.

In this Section the simplest scheme of clarification of the reasons of the malfunctions and refusals happening in knots and systems of the vehicle is offered. Refusals and their possible reasons are broken into groups on a sign of the relation to certain components or systems of the car as, for example the engine, the cooling system, etc., besides, in the text are given references to Chapters and Sections concerning these problems.

Remember that the successful completion of search of causes of defect is not the black magic available only to skilled professional mechanics at all, and is defined by a combination of a certain knowledge and patient, systematic approach to a problem research. It is necessary to move always from simple to difficult, to bring each check to the logical end and to try not to pass the obvious facts - everyone can forget to fill fuel in the fuel tank or to leave included in lighting fixtures for the night.

And at last, it is always necessary to try to make a clear picture of development of malfunction and to take the corresponding steps for prevention of a recurrence. If the failure of electric equipment happened for a cause of infringement of quality of contact, check a condition of all other contacts and electric sockets of system at the same time. If the same safety lock several times in a row continues to fuse, there is no sense in its further replacement - it is necessary to try to find out a cause of failure. Remember that failure of a minor component can be a sign of violation of functioning of more important knot or the whole system.

Engine

If the engine is not started, it is necessary to analyse a situation. That the petrol engine in general could be started, two main conditions have to be satisfied. Fuel-air mix has to come to cylinders, and on a spark plug the spark has to be developed. Therefore, first, it is necessary to check whether fuel moves. Address the Head of the Power supply system and release.

To define whether the spark is developed, it is necessary to turn out candles, to insert into tips and to put separately to weight. At the same time you do not hold a tip or a cable of ignition with hands, and use well isolated nippers. Ask the assistant to start the engine. If the spark is absent, address the Head Elektrooborudovaniye of the engine.

Procedures of diagnostics of an electronic control system and codes of malfunctions are provided in the Head Elektrooborudovaniye of the engine.

Start of the engine

Address also the Section Driving and auxiliary systems.

All engines

- RKPP: Tighten the parking brake, completely squeeze out a pedal of coupling and you hold it. Establish the check point in neutral situation. The switched-off coupling facilitates start of the engine, especially at low external temperatures since at the same time there is no friction from the check point.

- Automatic transmission: Install the selector in situation "P" or "N". Press a pedal of a brake and you hold it.

Do not include a starter more than 30 with continuously, otherwise the starter and cables overheat.


Petrol engine

· Turn the ignition key and include a starter, without giving at the same time gas. As soon as the engine starts working, release a key. If during 5 about the engine it is not started, press the accelerator pedal a little and again repeat start. If the engine is not started or at once stops, repeat start with half the squeezed-out accelerator pedal and if still start with completely squeezed out accelerator pedal is required.
At the hot engine during start slowly squeeze out the accelerator pedal.
· Surely at once begin the movement, only at a hard frost let's the engine get warm during 30 pages.

The unsuccessful, following one after another attempts of start of the engine can do harm to the catalytic converter since not burned down gasoline gets to it and when heating blows up.


Diesel engine

- On the cold engine: Include ignition and wait when the control lamp of preheat goes out. At once after the control lamp went out, start the engine, without giving at the same time gas. If at start there are irregular flashes, hold a starter included until then (but no more than 20 c) until the engine begins to work independently. If after all the engine is not started, turn the ignition key in situation "0" and wait for about 30 pages. After that once again make preheat and repeat start as it is described above.

While preheat is made, it is not necessary to include powerful electric consumers, otherwise the rechargeable battery without need is overloaded.


The diesel engine with direct injection, as a rule, demands use of preheat only at a temperature below 0 °C.


- On the warm engine preheat is not required. Start the engine at once, without giving gas.

The engine is not turned in attempts of its start

1. Corrosion of plugs of the battery takes place or fastening of tips of wires on them weakened. Check a condition of plugs and tips. Tighten terminal clips, if necessary remove corrosion traces.
2. The battery is discharged or faulty. If tips of wires are found by pure and reliably fixed on battery plugs, turn the ignition key in position of ON, then include headlights and/or screenwashes. If this electric equipment does not function, the battery is discharged.
3. Transmission it is inexact it is established in situation "P".
4. Conducting in a chain of system of start is torn off or fastening of wires on plugs weakened. Check a condition of wires, plugs and electric sockets of the battery, traction relay of a starter and the lock of ignition.
5. The gear wheel of a starter is jammed in a gear wreath of a driving disk. Try to turn the engine for a crankshaft pulley. At the first opportunity remove a starter and check a condition of a gear wheel and a gear wreath.
6. The traction relay of a starter (The head Elektrooborudovaniye of the engine) is faulty.
7. The starter (The head Elektrooborudovaniye of the engine) is faulty.
8. The ignition lock is faulty.

The engine is turned, but not started

1. Start is incorrectly made (Address the section Start of the Engine by means of the auxiliary rechargeable battery).
2. The engine immobilizator is faulty or is not disconnected.
3. The safety lock is faulty:

- Electric fuel pump;
- Electronic system of injection.
Concerning check of safety locks address the Head Kuzov.
4. The empty fuel tank or low-quality fuel is filled in.
5. The air filter is strongly polluted. Leak of vacuum in elements of air supply, malfunction in a control system of injection of fuel and ignition (Section Replacement of an Element of the Air Filter of the Engine) takes place.
6. The battery is discharged (the engine is turned too slowly). Check functioning of electric equipment (address the Section Automobile chemicals, oils and lubricants).
7. Korrodirovana terminal connections of the battery or their fastening weakened (address the Section Automobile chemicals, oils and lubricants).
8. The fuel pump is faulty, its safety lock fused or the pump relay is damaged. Check for hearing noise of operation of the pump at inclusion of ignition (The head of the Power supply system and release).
9. Components of system of ignition (The head Elektrooborudovaniye of the engine) are damaged or excessively moistened.
10. Spark plugs are worn-out or faulty or the candle gap (The head Elektrooborudovaniye of the engine) is incorrectly exposed.
11. Conducting of an electric contour of system of start is torn off or disconnected or fastening of wires on plugs weakened (address the Section Automobile chemicals, oils and lubricants).
12. Conducting of a contour of the coil of ignition is torn off or disconnected or fastening of wires on coil plugs (The head Elektrooborudovaniye of the engine) weakened.
13. The safety lock of the control unit of the engine is damaged, it is faulty any of sensors: The hall, the pulse sensor, the sensor of temperature of cooling liquid or the soaked-up air (The head Elektrooborudovaniye of the engine).
14. Too low pressure of a compression. Replace sealing laying of a head of cylinders. If necessary repair the engine.

Diesel engine:

1. Start is incorrectly made.
2. The engine immobilizator is faulty.
3. The safety lock is faulty:

· Electric fuel pump;
· Systems of preheat.
4. The engine is not heated-up: check serviceability of functioning of the device of preheat.
5. On the electromagnetic locking valve there is no tension. Connect to the switch the voltmeter or a sampler on a light-emitting diode. Include ignition. The light-emitting diode has to light up. Otherwise it is necessary to find break of an electrical wiring and to eliminate it.
6. The electromagnetic locking valve is faulty. Check reliability of fastening of the electromagnetic switch, check contacts. Switch on and off ignition. In the switch the click has to sound.
7. Damage to the line of supply of fuel or air to lines takes place:

a) Pipelines or hoses are mechanically damaged or littered. Clear fuel pipelines and remove air from lines and the filter.
b) The fuel filter is littered. Replace the filtering element.
c) It is necessary to check the filter and pipelines for availability of ice or wax in the winter. Put the car in the heated garage, add to system of gasoline.
d) Ventilation of a tank or the mesh filter of a toplivozabornik is littered. Clean.
8. Adjustment of the beginning of supply of fuel is brought down. Check, make adjustment.
9. Nozzles are faulty. Check. Turn off consistently cap nuts - at an otvorachivaniye of a nut of the faulty cylinder turns of the engine will not fall.
10. The fuel pump of high pressure (FPHP) is faulty. Establish new, or obviously serviceable TNVD for check.
11. Too low pressure of a compression. Replace sealing laying of a head of cylinders. If necessary repair the engine.

The starter functions without engine provorachivaniye

1. The starter gear wheel is jammed. Remove a starter (The head Elektrooborudovaniye of the engine) and check its state.
2. Teeth of a gear wheel of a starter or a wreath of a flywheel are worn-out or damaged.

Start of the cold engine is complicated


1. The battery is discharged or insufficiently charged.
2. Malfunction a component of a power supply system or electric equipment takes place (Chapters of the Power supply system and release and engine Electric equipment).
3. Paraffin in the filter of thin cleaning of the diesel engine. Replace a filter element. Fill winter fuel, or dilute with low-octane gasoline.
4. Glow plugs of the diesel engine are faulty.

Start of the hot engine is complicated

1. The air filter (The head of the Power supply system and release) is blocked.
2. Malfunction a component of a power supply system or electric equipment takes place (Chapters of the Power supply system and release and engine Electric equipment).
3. Fuel does not reach injectors of system of injection (The head of the Power supply system and release).
4. The corner of an advancing of supply of fuel of the diesel engine got off.
5. A low compression in cylinders, TNVD of the diesel engine is faulty or disadjusted.

Gearing of a starter happens is too noisy or with difficulty


1. Teeth of a gear wheel of a starter or a wreath of a flywheel are worn-out or damaged.
2. Bolts of fastening of a starter are lost or the effort of their tightening weakened.

The engine is started, but immediately becomes deaf


1. The engine immobilizator is faulty.
2. The electrical wiring is faulty or fastening of wires on plugs of the coil or the generator weakened.
3. Malfunction a component of a power supply system or electric equipment takes place (Chapters of the Power supply system and release and engine Electric equipment).
4. Basic installations of the block of electronic control (ESM) are broken.
5. Damage to system of release / catalytic converter.
6. Losses of depression through the pro-masonry surfaces of the inlet pipeline or block of injection of fuel take place. Make sure of reliability of an inhaling of fixing bolts / nuts, check the fact and quality of fastening on the unions on the inlet pipeline of all vacuum hoses. Check a condition of hoses and correctness of their connection (to the unions).

Stability of operation of the engine on single turns is broken


1. Leaks in the inlet air highway take place. Make sure of reliability of an inhaling of fixing bolts / nuts, check the fact and quality of fastening on the unions on the inlet pipeline of all vacuum hoses. Wiretap the working engine by means of a stethoscope or a piece of a fuel hose. Existence of the hissing sound will allow to reveal a source of "leak" of vacuum. It is possible to use solution of soap water for check not less effectively.
2. Malfunction a component of a power supply system or electric equipment takes place (Chapters of the Power supply system and release and engine Electric equipment).
· Serviceability of activation of an injector (Y62) and control of duration of injection is broken.
· Leaks through injectors / take place the epyura of injection is broken.
· It is faulty dokataliticheskiya a lambda probe of 1 (G3/3 or G3/4).
· Ignition tension level is insufficient.
3. The valve of system of the operated ventilation of a case is blocked (Head Dvigatel).
4. Zaklinyon, or allows leaks the EGR valve.
5. The air filter (The head of the Power supply system and release) is blocked.
6. The fuel pump does not provide giving of enough fuel to injectors of system of injection (The head of the Power supply system and release).
7. Leaks through laying of a head of cylinders take place. Perform measurement of compression pressure in engine cylinders.
8. Working ledges of cams of the camshaft are worn-out (Head Dvigatel).

Diesel engine:

1. Quality of connections of fuel hoses on TNVD and the fuel filter is broken. Replace fuel hoses, fix them by collars, tighten screws of angular connections.
2. Fastening of TNVD is mechanically damaged or weakened. Check fastening.
3. Are mixed by junctions of the returnable pipeline and pipeline of supply of fuel. Put connections on the places. The screw of connection of the returnable pipeline has marking of "OUT".
4. Damage to the line of supply of fuel takes place:

a) Pipelines or hoses are mechanically damaged or littered. Clear fuel pipelines.
b) The fuel filter is littered. Replace the filtering element.
c) It is necessary to check the filter and pipelines for availability of ice or wax in the winter. Put the car in the heated garage, add to system of gasoline.
d) Ventilation of a tank or the mesh filter of a toplivozabornik is littered. Clean.
5. Adjustment of the beginning of supply of fuel is brought down. Check, make adjustment.
6. Nozzles are faulty. Check. Turn off consistently cap nuts - at an otvorachivaniye of a nut of the faulty cylinder turns of the engine will not fall.
7. The fuel pump of high pressure (FPHP) is faulty. Establish new, or obviously serviceable TNVD for check.

Admissions of ignition take place during the operation of the engine on single turns


1. Spark plugs are worn-out or polluted or the candle gap (The head Elektrooborudovaniye of the engine) is incorrectly exposed.
2. Malfunction a component of a power supply system or electric equipment takes place (Chapters of the Power supply system and release and engine Electric equipment).
· Ignition tension level is insufficient; the measuring instrument of mass of MAF (B2/5) air is faulty.
3. Wires of spark plugs (The head Elektrooborudovaniye of the engine) are faulty.
4. Low-quality fuel is filled. The fuel filter is hammered.
5. Losses of depression in the inlet pipeline or through hose connections take place.
6. There is not enough, or compression pressure in cylinders is distributed unevenly. Perform measurement of a compression (Head Dvigatel).
7. Violations in work of a control system of the engine take place.

Admissions of ignition at the movement of the car on transfer take place


1. The fuel filter is blocked or pollution of a power supply system (The head of the Power supply system and release) takes place.
2. Spark plugs are faulty or polluted or the candle gap (The head Elektrooborudovaniye of the engine) is incorrectly exposed.
3. Malfunction a component of a power supply system or electric equipment takes place (Chapters of the Power supply system and release and engine Electric equipment).
4. Defect of candle wires (The head Elektrooborudovaniye of the engine) takes place.
5. Components of systems of decrease in toxicity of the fulfilled gases are faulty.
6. There is not enough or compression pressure is distributed between cylinders unevenly. Remove spark plugs and perform measurement of compression pressure (Head Dvigatel).
7. The system of ignition (The head Elektrooborudovaniye of the engine) is faulty.
8. Losses of depression on the throttle case, the inlet pipeline or through vacuum hoses take place.

The engine becomes deaf


1. Adjustment of turns of idling is broken.
2. The fuel filter is blocked and/or moisture or dirt (The head of the Power supply system and release) got to a power supply system.
3. The refusal a component of a power supply system or sensors (The head of the Power supply system and release) takes place.
4. Components of systems of decrease in toxicity of the fulfilled gases are faulty.
5. Spark plugs are faulty or polluted or the candle gap is incorrectly exposed (The head Routine maintenance). Also check a condition of candle wires (The head Elektrooborudovaniye of the engine).
6. Losses of depression on the case of a throttle or through vacuum hoses take place.

The engine does not develop full capacity


1. Malfunction a component of a power supply system or electric equipment takes place (Chapters of the Power supply system and release and engine Electric equipment).
· It is faulty dokataliticheskiya a lambda probe of 1 (G3/3 or G3/4).
· The sensor of temperature of cooling liquid (ECT) (B11/4) is faulty.
· The measuring instrument of mass of air (MAF) (B2/5) is faulty.
· Serviceability of functioning of system of resonant management of pressure pulsations in the inlet pipeline is broken; serviceability of functioning of the control system of a detonation is broken.
2. The air cleaner is littered. Clear or replace.
3. Spark plugs are faulty or the candle gap is incorrectly exposed (The head Routine maintenance).
4. The ignition coil (The head Elektrooborudovaniye of the engine) is faulty.
5. AT liquid level does not conform to requirements (The head Routine maintenance).
6. Coupling revolves (The head Stsepleniye and power shafts).
7. The fuel filter is blocked and/or dirt/moisture (The head of the Power supply system and release) got to a power supply system.
8. Fuel not of that grade is filled. Fill in in a tank fuel with the required octane number.
9. The adjusting valve of a turbocompressor is damaged.
10. The activator of a cam-shaft of shift of phases GRM is faulty.
11. Passability of the three-functional catalytic converter (TWC) is broken.
12. Compression pressure, insufficient or uneven on cylinders. Perform measurement of a compression which analysis of results allows to reveal existence of leakages of valves and/or violation of tightness of laying of a head of cylinders (Head Dvigatel).

In addition for the diesel engine

1. The air cleaner is littered. Clean or replace.
2. Uneven supply of TNVD fuel on cylinders. Adjust on the heated-up engine.
3. The moment of the beginning of supply of TNVD fuel is incorrectly determined. Establish.
4. The fuel filter or TNVD (nozzle) is littered. Wash out the preliminary filter, replace an element of the filter of thin cleaning, clean a spray or replace the pump (nozzle).
5. Adjustment of the maximum frequency of rotation of a bent shaft is broken.

There are cottons in system of an admission or shots in system of release


1. Malfunction a component of a power supply system or electric equipment takes place (Chapters of the Power supply system and release and engine Electric equipment).
2. Defect in a secondary contour of system of ignition (destruction of insulators of spark plugs or defects of candle wires) (The head Elektrooborudovaniye of the engine) takes place.
3. The system of injection of fuel needs adjustment or its components are excessively worn-out (The head of the Power supply system and release).
4. Losses of depression on the throttle case, the inlet pipeline or through vacuum hoses take place (address Section 8).
5. Valves (Head Dvigatel) are jammed.
6. The order of connection of candle wires (The head Elektrooborudovaniye of the engine) is broken.

At the movement with acceleration or uphill there are detonation sounds


1. Low-quality fuel is filled.
2. Malfunction a component of a power supply system or electric equipment takes place (Chapters of the Power supply system and release and engine Electric equipment).
3. Spark plugs not of that type are established. Check candles and coils for existence of damages (The head Elektrooborudovaniye of the engine).
4. Basic installations of the block of electronic control are broken.
5. The detonation sensor is faulty.
6. Depression losses take place.

Kalilny ignition takes place (the engine continues to work after switching off of ignition)


1. Idling turns are excessively high (Head Dvigatel).
2. Malfunction a component of a power supply system or electric equipment (The head Elektrooborudovaniye of the engine) takes place.
3. The valve of a purge of an adsorber of system of catching of vapors of fuel (EVAP) is damaged.
4. Working temperature of the engine is excessive. Decrease in level of a cooler (The head of the Cooling system and heating), failure of the thermostat, blocking of a radiator or malfunction of the water pump (The head of the Cooling system and heating) can be the possible reasons of this violation.

The diesel engine smokes


1. Black smoke:

a) The air cleaner is polluted. Wash out and fill with fresh oil or replace an element.
b) Inappropriate fuel is applied. Wash out a tank and replace fuel.
c) The moment of the beginning of giving of TNVD is incorrectly determined.
2. Blue smoke:

a) Burning of oil in the combustion chamber owing to wear of piston rings, high level of oil in the air cleaner, wear of epiploons in covers of a turbocompressor, formation of thinnesses in laying between a block case and a turbocompressor. Repair the engine, establish the normal level of oil, replace epiploons, tighten bolts of fastening of a turbocompressor or replace laying.
b) Fuel to one of nozzles does not move. Check on heating of final branch pipes of a collector.
c) Bad dispersion of fuel a nozzle because of malfunction of the valve or break of a spray. Grind in the valve or replace a nozzle.
3. White or brown smoke:

a) Low temperature in the cooling system. Check the thermostat.
b) Bad work of nozzles owing to wear or break of a spray. Replace a spray.

Engine electric equipment

Procedures of diagnostics of an electronic control system and codes of malfunctions are provided in the Head Elektrooborudovaniye of the engine.

The battery does not "hold" a charge


1. The driving belt of the generator is worn-out or damaged, or adjustment of its tension (The head Elektrooborudovaniye of the engine) is broken.
2. Level of electrolyte is insufficient or the battery (The head Elektrooborudovaniye of the engine) is strongly discharged.
3. Corrosion of plugs of the battery takes place or fastening of tips of wires on them weakened (The head Elektrooborudovaniye of the engine).
4. The generator does not provide the required charge current (The head Elektrooborudovaniye of the engine).
5. The electrical wiring of a charging contour is torn off or is in any other manner damaged or fastening of wires on plugs (The head Elektrooborudovaniye of the engine) weakened.
6. Short circuit of an electrical wiring creates continuous leakage of the current developed by the battery on weight (address the Head Elektrooborudovaniye of the engine and schemes of electric equipment).
7. Internal defect of the battery takes place.

The control lamp of charging does not die away at increase in turns


1. The driving belt is weakened. Check a natyazhitel of a maple belt.
2. Damage of the obgonny coupling. Remove the generator and turn a power shaft of the generator to the left. If the working surface of a pulley does not rotate, then damage, as a rule, to the obgonny coupling.
3. Damage of the regulator of the tension/generator. Disconnect a wire (D+) from a reverse side of the generator and include ignition. If now the control lamp does not light up, malfunction, as a rule, in the regulator of tension or in the generator.
4. Wear of brushes. Visually check brushes, if necessary replace.
5. Damage of the regulator. Check, if necessary replace.
6. Damage of the generator. Check, if necessary replace.
7. Damage of a wire between the generator and the regulator of tension.
8. Damage of the block of the dashboard.

The control lamp of charging does not light up at inclusion of ignition


1. Fused or otherwise the control lamp on the dashboard failed (The head Onboard electric equipment).
2. The generator (The head Elektrooborudovaniye of the engine) is faulty.
3. Defect of the printed circuit board, conducting in the block of the control panel or the boss of a lamp takes place (The head Onboard electric equipment).

The control lamp of a charge burns after switching off of ignition


Diodes are punched. Check diodes, replace a diode payment.

Starter

If the starter does not turn, at first it is necessary to check that on the plug of the 50th traction relay there was necessary tension of at least 10 Century. If tension is lower than this value, it is necessary to check according to the scheme of a wire, entering a starter current contour.

Whether the starter works at a full tension of the battery, it is possible to check as follows.

· Not including transfers, include ignition.
· Close starter plugs 30 and 50 a wire of section at least 4 mm2, address also materials of the Head Elektrooborudovaniye of the engine.

If the starter works faultlessly, the cause of defect should be looked for in wires to a starter. If the starter does not earn, it should be checked in the removed state.

Check condition: In places of connection of a wire have to be well fixed and should not be oxidized.

The starter does not rotate at turning on of the lock of ignition

1. The battery is discharged. Charge the battery.
2. Close starter plugs 30 and 50: The starter rotates. The break of a wire 50 to the ignition lock, is faulty the starter switch. Eliminate break, replace defective parts.
3. Break of a cable or the socket of weight, the battery it is discharged. Check cables and sockets of the battery, measure battery tension, if necessary load.
4. Insufficient passing of current owing to the weakened or oxidized sockets. Clear poles and plugs of the battery, check connections between the battery, a starter and weight.
5. There is no tension on the plug of the 50th traction relay. The break of a wire, the switch of a starter is faulty.

The starter rotates slowly and does not turn the crankshaft


1. Category of the battery. Charge the battery.
2. Summer oil is filled in. Fill in all-weather oil.
3. Insufficient passing of current owing to the weakened or oxidized sockets. Clear poles and plugs of the battery, check connections between the battery, a starter and weight.
4. Coal brushes do not adjoin to a collector, jam in guides, are worn-out, broken, greasy or polluted. Check brushes, clear or replace. Check guides.
5. Insufficient distance between brushes and a collector. Replace brushes and clear guides of brushes.
6. The collector in grooves or burned and was made oily. Process a collector or replace an anchor.
7. There is no tension on the plug 50 (min. 8 V). Check the switch of a starter or the traction relay.
8. The bearing is broken. Check the bearing, if necessary replace.
9. The traction relay is faulty. Replace the traction relay.

The starter grabs and rotates the engine breakthroughs


1. The gear wheel drive is faulty. Replace the gear wheel drive.
2. The gear wheel is polluted. Clear a gear wheel.
3. The gear wreath of a flywheel is faulty. Process a gear wreath if it is required, replace a flywheel.

The gear wheel of a starter does not depart from a wreath


1. The drive of a gear wheel or a carving are polluted or damaged. Clear or replace the gear wheel drive.
2. The traction relay is faulty. Replace the traction relay.
3. The returnable spring weakened or became torn. Replace a returnable spring.

The starter continues to work after an ignition key otpuskaniye


1. The traction relay jammed, is not switched-off. At once switch off ignition, replace the traction relay.
2. The ignition lock is not switched-off. At once switch-off the battery, replace the ignition lock.

System of electronic control

The cold engine does not enter the warming up mode


1. The sensor of temperature of ECT (B11/4) cooling liquid is faulty.
2. The measuring instrument of mass of MAF (B2/5) air is faulty.
3. Leaks in the inlet air highway take place.

The heated-up engine does not leave the warming up mode, or fuel consumption is increased


1. It is faulty dokataliticheskiya a lambda probe of 1 (G3/3 or G3/4).
2. The valve of management of a purge of an adsorber (Y58/1) is jammed in open situation.

The engine pulls


1. The measuring instrument of mass of MAF (B2/5) air is faulty.
2. Ignition tension level is insufficient; it is faulty dokataliticheskiya a lambda probe of 1 (G3/3 or G3/4).

The electronic control system of acceleration (EA) passed into emergency operation


1. The potentiometer of nominal rate in the sensor of provision of a pedal (B37) is faulty.
2. The potentiometer of the actuation mechanism of electronic control by acceleration / темпостата / systems of stabilization of turns of idling (EA/CC/ISC) is faulty.

Power supply system


Fuel consumption is excessive


1. The element of the air filter (The head of the Power supply system and release) is polluted or blocked.
2. Malfunction a component of a power supply system, electric equipment or electronic control takes place (Chapters of the Power supply system and release and engine Electric equipment).
3. Leaks in system of an admission of air.
4. Damages of system of release / catalytic converter.
5. Pressure in tires is not enough or tires not of that size are installed.

Diesel engine

1. Contamination of the returnable pipeline. Blow air the returnable pipeline from TNVD to the fuel tank.
2. Too high turns of idling and maximum turns. Adjust.
3. The engine has mechanical damages. Check a compression, if necessary repair the engine.

Leak of fuel takes place and/or there is a gasoline smell


1. There are leaks in lines of supply of fuel or ventilating lines (The head of the Power supply system and release).
2. The fuel tank is overflowed. You make gas station only before automatic shutdown of the gun.
3. Take place of leak or evaporation from lines of a power supply system and decrease in toxicity of the fulfilled gases (The head of the Power supply system and release).

The engine is not started


1. At inclusion of a starter the electric fuel pump does not work (noise from work is not heard). Slightly knock on a pump housing to release the jammed detail. Check whether tension is put to the pump. Check serviceability of a safety lock. Check electric contacts for good conductivity.
2. The relay of the fuel pump is faulty. Check the relay.
3. Giving of food from ECM (N3/10) is broken; the system of authorization of the driver (DAS) is faulty.
4. Valves of injectors stuck. Check injectors, if necessary replace. Check giving of tension for injectors. For this purpose to a rasstykuyta socket of injectors. Attach a diode control lamp to a wire and include a starter. The control lamp has to blink.
5. Ignition tension level is insufficient. There is no signal from the sensor of ignition of Hall or the sensor of temperature of cooling liquid. Check electric wires. Carry out a survey of memory of malfunctions.
6. Fuel pipelines are damaged, littered or untight, there are defects of hoses.
7. The fuel filter is littered.
8. The inlet system is untight. Additional air Podsasyvatsya.
9. Vacuum pipelines are damaged or untight.
10. Pressure regulator is damaged. Check residual pressure.
11. The sensor of provision of a butterfly valve is damaged.
12. There is no power supply of the block of electronic control by the engine.
13. Availability of ice or wax in the filter or pipelines of the diesel engine.
14. Ventilation of the fuel tank is hammered, the filter in a tank is littered.
15. Preheat of the diesel engine does not work or is not up to the end made.
16. The valve of a cut-off of fuel of the diesel engine is damaged.
17. The moment of the beginning of supply of fuel is brought down.
18. Nozzles of the diesel engine are damaged. Turn off in turn cap nuts and check whether the corresponding cylinder works.
19. TNVD is faulty.
20. The compression owing to excessive increase in pressure of oil is broken.

The cold engine is started badly, works unstably


1. Leaks in the inlet air highway take place.
2. Ignition tension level is insufficient.
3. The sensor of temperature of ECT (B11/4) cooling liquid is faulty. Check the sensor.
4. The measuring instrument of mass of MAF (B2/5) air is faulty.
5. Serviceability of activation of an injector (Y62) and control of duration of injection is broken.
6. Contents WITH does not conform to requirements. Check contents WITH and idling.
7. Pressure of fuel does not correspond to the required value. Check fuel pressure.

The warm engine is started badly, works unstably


1. Leaks in the inlet air highway take place. Check inlet system. For this purpose leave the engine to idle and cover places of consolidations and connection on an inlet path with gasoline. If speed for a short time increases, eliminate untight places. Remark: Vapors of gasoline are poisonous, do not inhale them.
2. Serviceability of activation of an injector (Y62) and control of duration of injection is broken.
3. The backpressure valve of the fuel pump is damaged.
4. Leaks in fuel system.
5. Elevated pressure of fuel in a power supply system.
6. Malfunction of system of catching of vapors of fuel.
7. The returnable fuel-supply line to a tank is hammered or crumpled.

The engine works with interruptions

1. Electric connections to the fuel pump are interrupted from time to time. Check a condition of shtekerny connections and sockets of electric wires of the fuel pump, measuring instrument of a stream of air and the relay of the fuel pump. Check a safety lock and places of contacts for the relay of the fuel pump. Clear contacts, if necessary replace.
2. Poor quality of fuel, formation of steam traffic jams. Fill qualitative fuel.
3. Too low volume of supply of fuel. Check pump productivity.
4. The fuel filter is faulty. Replace the fuel filter.
5. The fuel pump is faulty. Check the fuel pump.
6. Injectors are faulty. Check injectors.
7. It is faulty a lambda probe, violations in a chain of quality management of mix or there is no heating a lambda probe.
8. The sensor of provisions of a butterfly valve is faulty. Check the sensor of provisions of a butterfly valve.
9. The final collector or a reception pipe of system of release is damaged (there is leak of exhaust gases).
10. Fastening of fuel hoses to TNVD and the fuel filter of the diesel engine weakened.
11. At connection the giving and returnable TNVD pipelines are mixed by places.

The engine works with interruptions on the transitional modes and the mode of idling


1. The system of an admission of air is untight. Check connections of inlet system. Start the engine and grease with gasoline of the place of contact and connection in the soaking-up highway. If engine turns quickly increase, eliminate leakage.
2. Idling adjustment is incorrect. Check the idling regulator, the sensor of provisions of a butterfly valve, a lambda adjustment.
3. The sensor of full loading is faulty or incorrectly adjusted. Check the sensor of a butterfly valve.

The hot engine is not started


1. Incorrect adjustment of contents WITH. Check contents WITH and idling.
2. Too high pressure in fuel system. Check fuel pressure, if necessary replace pressure regulator.
3. The returnable pipeline between the regulator of pressure and the fuel tank is littered or bent. Clean or replace the pipeline.
4. The engine temperature sensor is faulty. Check temperature sensor.
5. The power supply system is untight. Make visual survey of all connections in the field of the engine and the electric fuel pump. Tighten all connections.
6. The system of an admission of air is untight. Check all connections of inlet system.

The engine works after switching off


1. Injectors are untight. Check injectors.
2. The fuel cut-off valve does not work at the diesel engine.

Lubrication system

The control lamp does not burn after inclusion of ignition


1. The oil pressure sensor is faulty. Include ignition, disconnect a wire from the sensor of pressure of oil and close on weight. If the lamp lights up, replace the sensor.
2. On the sensor tension, contacts of a korrodirovana does not move. Check electric wires and contacts.
3. The control lamp is faulty. Replace a control lamp.
4. The monitor is faulty. Replace the monitor.

The control lamp does not die away after start of the engine


Oil is overheated. Fir-trees the control lamp dies away after gas supply, it is required to do nothing.

The control lamp does not die away after supply of gas or lights up during the movement


1. Oil pressure too low. Check oil level, if necessary add. Check oil pressure.
2. The wire to the sensor of pressure of oil has short circuit on weight. Disconnect a cable from the sensor and take aside (without closing on weight), include ignition. If the lamp lights up, check a wire.
3. The sensor of pressure of oil is faulty. Replace the sensor.

Too low pressure of oil on all turns


1. In the engine there is not enough oil. Add oil.
2. The mesh filter is littered. Remove the case pallet, clear the mesh filter.
3. The oil pump is worn-out. Remove the oil pump and check it, if necessary replace.
4. Damages of bearings. Remove the engine.

Too low pressure of oil on small turns


The reducing valve stuck abroach because of pollution. Remove and check the valve.

Too high pressure of oil at speed over 2000 rpm


The reducing valve does not open because of pollution. Remove and check the valve.

Cooling system

Overheat


1. The cooler in system (The head of the Cooling system and heating) does not suffice.
2. The driving belt of the water pump is worn-out or damaged or adjustment of its tension is broken (Heads Routine maintenance and the Engine).
3. Internal channels of a radiator are blocked or it is polluted the front grille (The head of the Cooling system and heating) (is blocked).
4. The thermostat (The head of the Cooling system and heating) is faulty.
5. Fan blades (The head of the Cooling system and heating) are broken or burst.
6. The fan sensor switch is faulty. Check: at short circuit of red-yellow and red-white wires of the sensor the fan has to earn from half speed.
7. The index of temperature of cooling liquid is faulty. Check the sensor.
8. The pump of cooling liquid is faulty. Remove and check the pump.
9. Does not hold pressure a radiator cover. Make check of a cover under pressure.

Overcooling


1. The thermostat (The head of the Cooling system and heating) is faulty.
2. Indications of the measuring instrument of temperature are inexact.

External leakages of a cooler


1. Hoses are damaged or destroyed as a result of material aging or their fastening on unions weakened. Replace hoses and/or tighten collars of their fastening (The head of the Cooling system and heating).
2. Epiploons of the water pump are spoiled. In this case the cooler will exude through a control opening in a pump housing (The head of the Cooling system and heating).
3. Leaks from internal channels of a radiator or the side tank(s) take place. Repair of a radiator is required.
4. Leaks through a drain stopper of the engine (Head Dvigatel) or release traffic jams of water galleries (The head of the Cooling system and heating) take place.

Internal leakages of a cooler

Internal leakages of a cooler usually come to light by check of a condition of motive oil. Examine an edge of the measuring probe and internal surfaces of a cover (covers) of cylinders on existence of traces of water and foaming of oil.

1. Leaks through laying of a head of cylinders take place. Make check of the cooling system pressure.
2. There are cracks on a mirror of cylinders or in casting of a head. For check sort the engine (Head Dvigatel).

There are losses of a cooler

1. In system too much cooler (The head of the Cooling system and heating) is filled.
2. The cooler boils away as a result of an engine overheat.
3. Internal or external leakages of a cooler take place.
4. The radiator cover is faulty. Check a cover pressure.

Circulation of a cooler is broken


1. The water pump does not function properly. It is the simplest to make sure of functioning of the pump, having pressed the top hose of a radiator at the engine working at single turns. If at an otpuskaniye of a hose the liquid push in it is felt, the pump functions regularly (The head of the Cooling system and heating).
2. Passability of the cooling system is broken. Merge a cooler, wash out system and fill it with fresh mix (The head of the Cooling system and heating). If there is such need, remove a radiator (The head of the Cooling system and heating) and carry out its obratnopotochny washing.
3. The driving belt of the water pump is worn-out or damaged or adjustment of its tension is broken (Heads Routine maintenance and the Engine).
4. The thermostat (The head of the Cooling system and heating) is jammed.

Heater

The fan of a heater does not work


1. The fan motor safety lock is faulty. Check a fan safety lock, if necessary replace.
2. The fan switch is faulty. Check whether tension is put to preresistors, remove and check the fan switch.
3. The electric motor is faulty. Check whether tension at the included ignition and the closed fan switch is put to contacts of the motor of the fan. If tension is put, replace the motor.

The fan of a heater does not work at one of steps


The preresistor is faulty. Replace a connection payment.

The heater is not switched off by the regulator


1. The switch is faulty. Check the switch.
2. Cables of the adjusting mixing gate are damaged or badly mobile. Replace cables.

Too low power of heating


1. Too low level of cooling liquid. Check the level of cooling liquid, if necessary add.
2. The control unit of a heater has the heavy course, is faulty. Check the heater control unit, if necessary replace a cable.

Noise in the field of the heater fan


1. Dirt, leaves got. Remove the fan and clean it, clear the air channel.
2. Disbalance of a krylchatka, malfunction of the bearing. Remove the fan motor, check ease of the course.

Automatic Transmission (AT)

Procedures of diagnostics of an electronic control system of transmission and codes of malfunctions are provided in the Head Elektrooborudovaniye of the engine.
In view of complexity of a design of AT a component it is desirable to make diagnostics of its malfunctions and repairs in a workshop of car service or representative office of the Mercedes-Benz company.

The common problems connected with functioning of the mechanism of switching

1. It is possible to carry the following to number of the refusals connected with violation of adjustment of draft of switching:

a) Start of the engine is possible at provisions of transmission, excellent from "Р" (Parking) and "N" (Neutral).
b) Indications of the indicator of provision of transmission differ from really chosen transfer.
c) The car moves at the transmission established in situation "P" or "N".
d) Transfers switch hardly or randomly.
Make adjustment of draft of gear shifting (The head Automatic transmission).

Transmission revolves, switches hardly, publishes extraneous noises or does not provide the movement of the car at installation on one of lobbies or the reverse gear


1. There is a set of the possible reasons of the problems listed in heading, however under competence of the amateur mechanic only one of them - the wrong level of transmission liquid gets.
2. Before driving away the car in a workshop of car service check the level and a condition of transmission liquid (The head Routine maintenance). Modify level according to requirements of Specifications or replace liquid together with the filter. If the situation did not improve, ask for the help experts.

Leak of transmission liquid takes place


1. AT liquid has dark red color. Traces of its leaks should not be confused to traces of motive oil which can be demolished on a transmission case by the running air stream.
2. For identification and localization of a source of leak first of all remove all traces of dirt and lubricant from the transmission boat. Use suitable degreaser and/or make steam cleaning. Then make on the car a short trip at a small speed (that traces of leak did not communicate the running stream far from its source). Stop, the car and by visual survey establish to a poddomkratta a leak source. Most often act as those:

a) Transmission case pallet: Tighten fixing bolts and/or replace laying of the pallet.
b) Tube of the gulf of liquid: Replace rubber consolidation in the place of an entrance of a tube to a transmission case.
c) Lines of transmission liquid: Tighten nipple connections or replace lines.
d) Ventilating tube: Transmission is crowded and/or water got to it.

Oil has brown color or smells of ashes


Low level of liquid in a box (address the Head Routine maintenance).

The Kickdown mode does not join by full pressing a pedal (the low gear does not join)


1. Low level of liquid in a box (address the Section Check of Level of Oil of Automatic Transmission).
2. Malfunction in a control system of the engine (address the Head Elektrooborudovaniye of the engine).
3. Malfunction of the sensor or its conducting (address the Head Automatic transmission).
4. Adjustment of a cable of the selector is broken (address the Head Automatic transmission).

The engine is not started at any position of the selector or started in any situation except P and R


1. Adjustment of the sensor of permission of start is broken (address the Head Automatic transmission).
2. Malfunction in a control system of the engine (address the Head Elektrooborudovaniye of the engine).
3. Adjustment of a cable of the selector is broken (address the Head Automatic transmission).

Transmission revolves, breakthroughs or noise at gear shifting. The car does not move at inclusion of the D or R modes


1. Low level of liquid in transmission (address the Section Check of Level of Oil of Automatic Transmission).
2. Malfunction of the sensor or its conducting (address the Head Automatic transmission).
3. Malfunction in a control system of the engine (address the Head Elektrooborudovaniye of the engine).

Bridges

Extraneous noises


1. Usual road noise. Adjustment is not given in.
2. Noise of tires. Check a condition of protectors and pressure of a rating of tires.
3. Bearings of wheels are worn-out or damaged, or the effort of their tightening weakened.

Vibrations


Check a condition of bearings of wheels, serially poddomkrachivy corresponding from corners of the car and rotating a wheel manually. Listen at the same time to the sounds proceeding from the bearing. Remove bearings and check their state.

Oil leak


Epiploons of power shafts are damaged (The head Stsepleniye and power shafts).

Brake system

Before coming to final conclusion about existence of problems with the brake system make sure that tires are in satisfactory condition and are beefy with the required pressure, adjustment of angles of installation of forward wheels is not broken and the car is not loaded unevenly.

The increased brake pedal course

The brake contour failed. Check whether brake fluid follows.

The pedal of a brake springs and fails


1. Air in the brake system. Remove air from system.
2. There is not enough liquid in the tank. Add new brake fluid, remove air from system.
3. Formation of vials of steam. It is shown, mainly, at big load of brakes. Replace brake fluid, remove air from system.

Decrease in effect of braking, pedal fails


1. Leakage of the pipeline. Delay connections of the pipeline or replace tubes.
2. Damage of cuffs to the main thing or working brake cylinders. Replace a cuff. In the main brake cylinder replace internal elements, if necessary replace the main cylinder.
3. Rubber laying is damaged. Repair a support.

Bad braking, despite big effort of pressing of a pedal


1. Brake slips are greasy. Replace brake shoes.
2. The improper or hardened blocks are established. Replace blocks. Address the section Acquisition of Spare Parts.
3. The brake amplifier is faulty. Check the brake amplifier.
4. Brake shoes are worn-out. Replace brake shoes.

When braking the car takes away aside


1. Pressure in tires does not correspond to demanded. Check and modify pressure in tires.
2. Uneven wear of tires. Replace worn-out tires.
3. Brake shoes are greasy. Replace blocks.
4. On one axis different brake shoes are established. Replace blocks. Address the section Acquisition of Spare Parts.
5. Bad condition of brake shoes. Replace blocks.
6. Mines of supports are polluted. Clear guides and landing surfaces of blocks in a support.
7. Corrosion of cylinders of brake supports. Replace a support.
8. Uneven wear of a brake shoe. Replace brake shoes (on both wheels).

Spontaneous braking


1. The compensation opening in the main brake cylinder is littered. Clean the main cylinder and replace internal elements.
2. Too small gap between a driving rod and the piston of the main brake cylinder. Check a gap.

Brakes heat up during the movement


1. The compensation opening in the main brake cylinder is littered. Clear the main cylinder and replace internal elements.
2. Too small gap between a driving rod and the piston of the main brake cylinder. Check a gap.
3. The drosseliruyushchy opening in the special valve on the bottom is littered. Clear the main brake cylinder, replace internal elements and brake fluid.

Brakes shiver


1. Blocks of inadequate type are established. Replace blocks. Address the section Acquisition of Spare Parts.
2. Brake disk in places корродирован. Carefully grind a brake disk.
3. The brake disk has a side beating. Process a disk or replace.

Brake shoes do not depart from a brake disk, the wheel is hardly turned by a hand


Corrosion in cylinders of brake supports. Repair a support, perhaps replace.

Uneven wear of blocks


1. Blocks of inappropriate type are established. Replace blocks. Address the section Acquisition of Spare Parts.
2. The support is polluted. Clear the mine of a support.
3. Heavy piston stroke. Eliminate.
4. The brake system is untight. Check tightness of the brake system.

Wedge-shaped wear of brake shoes


1. The brake disk rotates not parallel to a support. Check support prileganiye surfaces.
2. Corrosion in supports. Eliminate pollution.
3. The piston works incorrectly. Check position of the piston.

Scratch of brakes


1. Often the reason in atmospheric influence (humidity of air). If the scratch appears after the long parking at the increased humidity and then vanishes, it is not necessary to do anything.
2. Blocks of inappropriate type are established. Replace blocks, cover basis plates with protivoskripny paste. Address the section Acquisition of Spare Parts.
3. The brake disk rotates not parallel to a support. Check surfaces of a prileganiye of a brake support.
4. The mine of a support is polluted. Clear the mine of a support.
5. Springs of fastening of blocks are bent. Replace fastening springs.
6. Press springs are stretched. Replace press springs.

Brake pedal pulsation


1. ABS in operation. Normally, the help is not required.
2. Too big side beating or the admission on thickness of a brake disk. Check a beating and thickness. Process or replace a disk.
3. The brake disk rotates not parallel to a support. Check a support prileganiye surface.

The control lamp of ABS lights up during the movement


1. Too low voltage of food (it is lower than 10 V). Check tension. Check whether the control lamp of the generator after start of the engine dies away. If everything is all right, check maple a generator drive belt.
2. ABS damage. Check reliability of contact and presence of corrosion of accession of weight at the returnable pump (in the hydraulic block).

Suspension bracket and steering

The car takes away at the movement in one of the parties


1. Tires are pumped unevenly up.
2. Defect of tires takes place.
3. Components of a suspension bracket or steering are excessively worn-out (The head Podvesk and steering).
4. Carrying out adjustment of angles of installation of forward wheels is required.
5. Forward brake mechanisms are taken (The head the Brake system).

Breakthroughs, pulling or vibrations take place


1. Balancing of wheels is broken or ovality of disks appeared. Make balancing in a tire workshop.
2. Bearings of wheels are worn-out, the effort of their tightening weakened or adjustment is broken (The head Podvesk and steering).
3. Racks shock-absorbers or other components of a suspension bracket are worn-out or damaged (The head Podvesk and steering).

Excessive rocking of the car or "zaryvany" his nose on turns takes place or when braking


1. Shock-absorbers of racks of a suspension bracket are faulty. Replace racks entirely (The head Podvesk and steering).
2. Suspension bracket components are damaged. Make check of a state a component (The head Podvesk and steering).

Too hardly the steering wheel rotates


1. Excessively liquid level fell in the tank of system of hydrostrengthening of a wheel (The head Routine maintenance).
2. Tires are pumped incorrectly up.
3. Hinges of the steering drive are insufficiently greased (The head Podvesk and steering).
4. Adjustment of angles of installation of forward wheels is broken.
5. The hydraulic booster does not develop the required power.

The excessive side play of steering takes place


1. The inhaling of bearings of forward wheels weakened (The head Podvesk and steering).
2. Components of a suspension bracket or steering are excessively worn-out (The head Podvesk and steering).

The system of hydrostrengthening of a wheel does not develop due effort


1. The driving belt of the pump of the hydraulic booster is worn-out or damaged or adjustment of his tension is broken (The head Routine maintenance).
2. Excessively liquid level fell (The head Routine maintenance).
3. Passability of hoses or lines of hydraulic system is broken. Check, in case of need make replacements.
4. Air got to hydraulic system. Pump over system (The head Routine maintenance).

Excessive wear of protectors takes place (not in one some area)


1. Tires are pumped incorrectly up.
2. Balancing of wheels is broken. Address in a tire workshop.
3. Disks of wheels are damaged. Check, in case of need make replacement.
4. Components of a suspension bracket or steering are excessively worn-out (The head Podvesk and steering).

Excessive wear of protectors on an outer edge takes place


1. Tires are pumped incorrectly up.
2. Turns are too sharply made. Reduce speed.
3. Adjustment of angles of installation of forward wheels (excessive convergence) is broken. Address in a workshop for carrying out professional adjustment.
4. The suspension bracket lever is bent or deformed (The head Podvesk and steering).

Excessive wear of protectors on an inner edge takes place


1. Tires are pumped incorrectly up.
2. Adjustment of angles of installation of forward wheels is broken (divergence). Make adjustment in a workshop of car service.
3. Components of steering are damaged or their fastening weakened (The head Podvesk and steering).

Local wear of a protector takes place


1. Balancing of wheels is broken.
2. Disks are damaged or bent. Check, in case of need make replacement.
3. Defect of tires takes place.

Defects of brushes of a screen wiper

Slipping


1. Elastic bands are polluted. Clear elastic bands a rigid nylon brush and solution of detergent or alcohol.
2. Shabby edges of brushes, elastic bands are worn-out or broken off. Replace elastic bands.
3. Old elastic bands, the cracked surfaces. Replace elastic bands.

In the field of cleaning the water remains gather in drops at once


The windshield is polluted by varnish polish or oil. Clear a windshield a pure rag with an eliminator of lubricant, oil, silicones.

The brush clears unilaterally - in one party well, in another is not present


1. The elastic band is deformed in one party "does not overturn any more". Establish a new elastic band.
2. The lever of a screen wiper is twisted, the brush not precisely adjoins to glass. Carefully turn the lever, vertical position will not be reached yet.

Crude surfaces


1. The elastic band escaped from a frame. Carefully insert an elastic band into a frame.
2. The brush adjoins to glass unevenly as spring levels or plates are bent. Replace a brush. This malfunction, first of all appears at negligent installation of a spare brush.
3. Pressing force the lever is too small. Slightly grease hinges of levers of a screen wiper and spring or install the new lever.

Defects of tires

Strong wear of the tire on both parties of a working surface


Too low pressure in tires.

Strong wear of the tire in the middle of a working surface, on all circle


Too high pressure in tires.

Uneven wear of a protector


Static and dynamic disbalance of a wheel. Perhaps too big side beating of a disk, too big side play in the bearing hinges.

Uneven wear in the middle of a protector


Static disbalance of a wheel. The consequence of a strong vertical beating is possible.

Strong wear of certain places in the middle of a working surface


Blocking traces at sharp braking.

Sawtooth wear of a protector. Often together with a rupture of a fabric basis which is not visible outside


Car overload. Check an internal part of the tire for ruptures of a basis.

Rubber uvulas on side edges of a protector


Wrong adjustment of angles of installation of wheels. The tire is worn-out. Check also a condition of racks shock-absorbers.

Formation of agnails on one party of a protector of a forward wheel


Wrong adjustment of a convergence. The tire is worn-out. Frequent movement on wavy surfaces. The Bystry movement on turns.

Ruptures of a cord. At first are visible only from within


Moving through sharp stones, blows of tires, etc. at a high speed.

Unilaterally worn-out working surface


1. Check adjustment of disorder.
2. ABS damage. Check reliability of contact of connection with the case at the returnable pump (in the hydraulics block).